CUSTOMER
SUCCESS STORIES

Banner Image
×

The Royal MTC™ Turns 4-Hour Chuck Swaps
into 10-Minute Changeovers

AT A GLANCE:

  • Customer: In-House R&D machine shop at a rigid plastic packaging manufacturer
  • Regional Manager: Matt Block
  • Application: Prototype and spare-part mold components for stretch blow molding equipment
  • Machine: DN Solutions Puma 2600
  • Material: Tool Steels
  • Royal Solution: Royal MTC™ Multi-Tasking Chuck (MTC-320)
  • Key Result: Changeovers cut from 4 hours to 10 minutes, rush jobs run without tearing down, and zero issues in 9 months of use
THE CHALLENGE: Eliminate Hours-Long Chuck Changeovers on a High-Mix Lathe

This customer’s R&D site runs as an in-house job shop for a rigid plastic packaging manufacturer. They make mold components and spare parts for the machines that produce bottles for everything from spirits to shampoo to hand sanitizer. Parts range from 1/2″ to 6″ in diameter and quantities are small, often just 6 to 10 pieces. Lately 80% of the shop’s jobs are for maintenance parts, so fast turnaround matters.

For parts up to 3″ in diameter they’ve relied on their Royal Quick-Grip™ QG-80 collet chuck. It’s provided ultra-precision accuracy and quick changeover on small diameter work, but for larger parts they’ve needed to switch to their 10″ 3-jaw chuck. Every swap meant maneuvering a crane cart into place, removing one chuck, mounting the other one, indicating it in, and reconfiguring the parameters for collision avoidance. Each swap took around four hours.

In short, losing half a day to change over from one chuck to another was killing throughput, efficiency, and uptime.

THE SOLUTION: The Royal MTC™ Multi-Tasking Chuck

Regional Manager Matt Block recommended the Royal MTC™ Multi-Tasking Chuck, and the shop installed a 12″ MTC-320 on the Puma 2600. The MTC™ combines a 3-jaw chuck, Quick-Grip™ collet chuck, ID and 5C workholding system all in one body. Since the chuck stays on the spindle, switching functions is simply a matter of swapping the quick-change center hub.

Installation was easy – Matt was only on site for about an hour total, including uncrating. That single MTC™ now covers the shop’s full range of work, from 6″ parts down to 1/2″. Larger parts run in the 3-jaw, most parts up to 3″ run in Royal Quick-Grip™ collets, and the 5C adapter provides a dedicated option for their smallest parts (down to 1/16”). Since the MTC™ uses Royal QG collets and industry-standard 60° x 1.5mm serrated base jaws, the shop has been able to get more use out of their prior workholding accessories.

THE RESULTS: Changeovers in Minutes, Rush Jobs Without the Teardown, and Zero Issues!

Changeovers that took four hours now take 10 minutes or less, even when swapping all the way from a 1/2″ part in 5C to a 4″+ part in the 3-jaw. The process is so quick that setting the jaw position takes longer than the swap itself. For parts under 3″, changing Quick-Grip™ collets takes only a few seconds.

The shop now changes over several times a day. It can pause a longer job mid-run, switch over for an expedited part, then return to the original job without skipping a beat. The best aspect is “the ease and the time to go between a large-diameter part and a small-diameter part. Normally that would’ve taken me half a day to pull the chuck,” the customer said.

In the nine months since installation, the MTC™ has had zero issues and hasn’t come off the spindle. The customer is pleasantly surprised by the excellent repeatability, saying that there have been no runout issues – even with frequent changeovers. Upkeep is simply greasing and cleaning the chuck at each change.

Cutting changeover time from half a day to only 10 minutes, the MTC™ has transformed how this R&D shop handles high-mix, low-volume work. This customer is so happy with the setup that they’ve invited Royal to bring other potential customers in to check it out in person.